Reset the Range Rover Airbag Fault Code

Instructions

1. Open the hood and loosen the retaining nut on the cable clamp running to the negative battery terminal.

2. Slide the clamp off of the negative battery terminal.

3. Wait 1 minute for the Range Rover’s electronic control module to cycle and reset. Then, reconnect the clamp to the negative battery terminal.

4. Tighten the retaining nut on the cable clamp. The airbag light should go out at this point. When it does, you’ll know that the fault code has been erased.

Renault Scenic service indicator light reset

To reset the service indicator on the scenic II is as follows:
Scroll through the trip computer using the button on the end of the right hand stalk control until you get to the miles till service indicator (or the “change oil soon message” will appear if due)
Then press and hold the same button in and hold it. The miles indicator will then flash then change to 18000, keep the button pressed until the 18000 stops flashing.

NOTE: If the word “service” appears on your dash then that does NOT mean that a service is due. It is an indication that the vehicle is faulty and has a stored major fault code.

The indicator that a Service is due is when the words “change oil soon” appears or the spanner starts flashing.

Reset the Service Lights on a BMW 1-Series

Many models in the BMW 1-series are equipped with a maintenance system that monitors driving conditions to calculate when regular maintenance should be completed. When the computer determines it is time for regular service, a reminder light is illuminated on the control panel. After the scheduled service is performed, the service lights should be reset in order for the computer to accurately track when the next service will be due.

Instructions

1. Insert the key into the ignition.

2. Press the “Start/Stop” button. Wait for the service reminder lights to turn on and off.

3. Press and hold the trip odometer “Reset” button.

4. Release the “Reset” button when the service menu appears.

5. Press the “Menu” button on the end of the turn signal arm to move through the menu until the service reset option is highlighted.

6. Press and hold the “Reset” button until the service light resets.

Oil service reset Aurora

1995

Turn the ignition to run (one position before starting engine).
Press the test button and release.
Press OIL button and release.
Press and hold the RESET button for 5 to 7 seconds.
Turn the ignition off and then start the engine to verify the indicator has been reset.

1996-1997

Turn the ignition to run (one position before starting engine).
Display the oil life index on the Driver Information System.
Hold the reset button for 5 seconds.
Turn the ignition off and then start the engine to verify the indicator has been reset.

1998

Turn the ignition to run (one position before starting engine).
Press the ENG button on the DIC control panel until the OIL LIFE percentage appears.
Press and hold the RESET button for more than 5 seconds. The word RESET appears. Then the message OIL LIFE 100% appears.
Turn the ignition off and then start the engine to verify the indicator has been reset.

2001-2003

Turn the ignition to run (one position before starting engine).
Press the RIGHT arrow button on the DIC until OIL LIFE percentage is displayed.
Press RESET and hold for 5 seconds. OIL LIFE 100% will appear and then when the button is released OIL LIFE 100% will be displayed.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil light reset Jeep Renegade Concept

Many Jeep vehicles track the intervals between oil changes to alert the driver when the next oil change is needed. A light illuminates on the control panel when the internal system determines it is time for an oil change. Most Jeep mechanics reset the oil light as part of the oil change service. If you change the oil in your Jeep yourself, you can manually reset the oil light. Resetting the oil light after an oil change allows the system to accurately track the time until the next oil change is needed. The procedures described in this article apply to 2010 Jeep models.

Instructions

1.Turn the ignition switch to the “ON” position. Do not start the engine.

2.Press the accelerator pedal completely to the floor slowly three times within a 10-second span.

3.Turn the ignition switch to the “OFF” position.

4.Turn the ignition switch to the “ON” position again. The oil light should be off. If the oil light is still illuminated, repeat the previous steps.