2010 Dodge Grand Caravan how to reset oil light

To reset the oil change indicator system (after
performing the scheduled maintenance), refer to the
following procedure:

1. Turn the ignition switch to the ON position (Do not
start the engine).
2. Fully depress the accelerator pedal slowly three times
within 10 seconds.
3. Turn the ignition switch to the OFF/LOCK position.
NOTE: If the indicator message illuminates when you
start the vehicle, the oil change indicator system did not
reset. If necessary repeat this procedure.

ibiza/cordoba 93-99 service indicator system

SERVICE INTERVAL DISPLAY

the computer has counters that not only count the miles from the speedo but also
a time count as well

Displays:

IN00 – No service is required – standard display

OEL – When 7500 miles has been reached before the yearly service is required

IN01 – Indicates time for the yearly service inc oil change

IN02 – Indicates it is time for the Major service

TO RESET THE INDIVIDUAL COUNTERS

1- turn on ignition (do not start)

2- Press the trip-reset button button on the speedo (the trip value will not reset to
zero but will reappear when the procedure is finished)

3- Turn off the ignition and thne release the trip-reset button

In the LCD display you will see the word “OEL”

Using the minute set button for the clock (lower one) you will reset the OEL interval
counter

press it – hold – release – 5 horizontal lines will appear in the display

4- press and release the trip-reset button

In the LCD display you will see “IN01” repeat step 3 to reset the inspection counter when required

5- Again press the trip-reset and rest the “IN02” counter if necessary

If doing an oil change only reset the “OEL” counter

If doing an inspection service reset both the “OEL” and “IN01” counters

If doing a full service reset all 3 – “OEL” “IN01” & “IN02”

6- Turn on ignition (do not start the car)

7- After the appearance of the “IN00” display turn off the ignition

8- You are done – the trip counter should read as it did before you started

PROGRAMMING THE INTERVALS TO REQUIREMENTS

With todays higher spec oils and/or peoples need and desire to service more regular there is a way
to alter the counters to your prefered settings (within reason)

1- Turn on ignition (don’t start the car)

2- press the trip-reset button also press the Minute set button on the clock (lower one)

3- The LCD display “OEL 1,S” where the “S” indicates SET

4- Using the trip-reset button you can call up the following counter data in sequence

OEL 1,S – Distance counter for oil change (7500 standard)

OEL 2,S – Time counter for oil change (12 months)

IN 01,S – Time counter for yearly service interval (12 months)

IN 02,S – Distance counter for full service (15000 miles)

5- Using the minute SET button on the clock (lower one) you can display the current value
repeated pressing of the button will select a subsequent lower value and at the lowest level
will reset to the highest and start to decrease again (so don’t panic)

the steps work in miles (500 at a time) and time steps in bi-monthly (1=2months) i.e.1-2-3-4-5-6

6- Once you have set the counter to the value you require – turn off the ignition

7- Job done

Oil service reset Jeep Commander

Engine Oil Change Indicator System

Oil Change Required
Your vehicle is equipped with an engine oil change
indicator system. The “Oil Change Required” message
will flash in the EVIC display for approximately 10
seconds after a single chime has sounded to indicate the
next scheduled oil change interval. The engine oil change
indicator system is duty cycle based, which means the
engine oil change interval may fluctuate dependent upon
your personal driving style.
Unless reset, this message will continue to display each
time you turn the ignition switch to the ON/RUN
position. To turn off the message temporarily, press and
release the MENU button. To reset the oil change indicator
system (after performing the scheduled maintenance)
refer to the following procedure.

1. Turn the ignition switch to the ON position (Do not
start the engine).

2. Fully depress the accelerator pedal slowly three times
within 10 seconds.

3. Turn the ignition switch to the OFF/LOCK position.

NOTE: If the indicator message illuminates when you
start the vehicle, the oil change indicator system did not
reset. If necessary repeat this procedure.