Tag: lamp

BMW X5 2002 Oil Reset

BMW X5 Engine Oil Service reset

Turn the ignition to “0”
Press and hold odometer button and turn the ignition to “1”.
Hold odometer button pressed for approximately 5 seconds until the display shows: “Inspektion Re /
Release and press odometer button again until Reset flashes
Release and press odometer button shortly.
Release and press odometer button again.
The next oil service interval will be shown and will disappear.
Oil service lamp is now reset

Note: To abort the procedure at any time: turn the ignition to “0”.

Volvo 850-70 Service Light Reset

RESETTING 5000 MILE SERVICE LAMP ON 1994 + 1995 850

NOTE: This function is for the service reminder lamp, be sure you have performed the proper service such as changing the oil before resetting. If the check engine lamp is illuminated when the car is running, you’ll need to have the car looked at by the Volvo dealer for proper diagnosis.

1. Turn on the ignition to the KPII position so the warning lamps on the dash are illuminated. Do not start the car.

2. Open the bonnet of the car and locate Diagnostic test port (A) behind the driver side headlamp.

3. Remove the cover and pull the jumper wire out of the holder in the cover.

4. Insert the jumper into terminal #7, then press button 4 times, wait approximately 5 seconds and the red lamp should glow continuously. You are now in the data reset mode.

5. Press the button 1 time and wait approximately 5 seconds for the lamp to glow again then press the button 5 times. After about 5 seconds the lamp will illuminate again, press the button 1 time and you will see the lamp flash repeatedly for a couple of seconds indicating that the service lamp has been properly reset.

6. If a mistake is made, simply switch the ignition off and back on to reset and start over.

1996 Model (Some of them)
On these models the diagnostic socket is in front of the gear stick. Switch the ignition on. As you look at the speedometer on the dash, beneath it opposite the trip reset button is a rubber plug. Remove the plug and with a thin pointer such as a ball point pen, depress the pin. This will reset the service light.

1999 Model Service Lamp Reset Procedure

1. Press and hold trip odometer reset button

2. Turn ignition key to run position KPII (not the start position)

3. Wait 30 seconds or until service light begins blinking

4. Release Trip Odometer button

5. Turn ignition to off position

Oil service reset Alero

1999-2003

Turn the ignition to run (one position before starting engine).
Push the RESET button located in the drivers instrument panel fuse block. The CHANGE OIL light will start to flash.
Press and hold the RESET button again. The reset is complete when you hear the chimes and the CHANGE OIL light goes out.
Turn the ignition off and then start the engine to verify the indicator has been reset.

2004

Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds. The reset is complete when the chimes sound and the CHANGE OIL lamp goes out. If the lamp stays on and and no chime is heard, repeat the reset procedure.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Service oil reset Honda Accord

1982-1985
After completing the oil change, the maintenance lamp may be reset by inserting the ignition key into the appropriate slot on the instrument panel below the indicator lamp. The indicator will change to green.
1986-1991
Insert ignition key into slot below indicator flag at lower right corner of instrument cluster.
Push key in until indicator changes from red to green.
1992-1996
Insert ignition key into centre slot located on the front of the instrument cluster. When reset, the indicator changes to green.
1997-1999
With Reset Button on Instrument Panel:
Turn the ignition off.
Press the select switch and reset switch at the same time, turn the ignition switch to run (one position before starting).
Hold them for at least 10 seconds, until the indicator resets.
Turn the ignition off and then start the engine to verify the indicator has been reset.
With Key Slot on Instrument Panel:
Reset the indicator by inserting the key in the slot and changing the indicator to green.
2000-2005
Turn off the engine.
Press and hold the SELECT/RESET button in the instrument panel. and turn the ignition switch ON (ii).
Hold the button for at least 10 seconds, until the indicator resets.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2006-2010
Turn the ignition to run (one position before starting engine).
Press the SELECT/RESET knob until the engine oil life indicator is displayed.
Press the SELECT/RESET knob for more than 10 seconds. The engine oil life indicator and the maintenance code(s) will blink.
Press the SELECT/RESET knob for more than 5 seconds. The maintenance items code(s) will disappear, and the engine oil life will reset to 100.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Service oil reset Chevrolet Caprice

1994
Remove the instrument panel fuse box cover.
Turn the ignition to run (one click before starting).
Press the OIL RESET button for 5 seconds and the change oil lamp should go off.
Turn the ignition off and then start the engine to verify the indicator has been reset.

1995-1996
Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds.
If CHANGE ENGINE OIL light does not go out, turn off the ignition and repeat steps 1-3.
Turn the ignition off and then start the engine to verify the indicator has been reset.