Tag: change

Oil service reset Eighty-Eight

1994-1995

Engine Oil Life Monitor
Turn the ignition to run (one position before starting engine).
Display the oil life index on the Driver Information System.
Hold the RESET button for 5 seconds. When a DIC message of RESET is displayed and the oil life index equals 100%, the reset is complete.
Turn the ignition off and then start the engine to verify the indicator has been reset.
Change Oil Soon
Turn the ignition to run (one position before starting engine).
Press OIL button and release.
Select OIL menu by pressing MODE button.
Press and hold the RESET button for 5 to 7 seconds.
Turn the ignition off and then start the engine to verify the indicator has been reset.

1996-1997

Turn the ignition to run (one position before starting engine).
Display the oil life index on the Driver Information System.
Hold the RESET button for 5 seconds.
Turn the ignition off and then start the engine to verify the indicator has been reset.

1998

Turn the ignition to run (one position before starting engine).
Press the TRIP button on the Driver Information System (DIC) switch to view various menu choices and stop on OIL LIFE REMAINING.
Press and hold the RESET button on the DIC switch for more than 5 seconds. The oil life will change to 100%. The engine oil life monitor is now reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.

1999

Turn the ignition to run (one position before starting engine).
Press and hold the OIL RESET button in the IP storage compartment for at least 5 seconds, but no more than 60 seconds.
After 5 seconds, observe the CHANGE OIL SOON light flash 4 times before light turns off. This indicates that the engine oil life monitor system has reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset Cutlass Supreme

1996

Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds. If the CHANGE OIL SOON indicator flashes 2 times, the system is reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.

1997

Turn the ignition to run (one position before starting engine).
Display the oil life index on the Driver Information System.
Hold the reset button for 5 seconds.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset Bravada

2002-2004

Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds. If the CHANGE ENG OIL light flashes for 5 seconds, the system is reset. If the light does not flash, repeat the procedure.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset Alero

1999-2003

Turn the ignition to run (one position before starting engine).
Push the RESET button located in the drivers instrument panel fuse block. The CHANGE OIL light will start to flash.
Press and hold the RESET button again. The reset is complete when you hear the chimes and the CHANGE OIL light goes out.
Turn the ignition off and then start the engine to verify the indicator has been reset.

2004

Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds. The reset is complete when the chimes sound and the CHANGE OIL lamp goes out. If the lamp stays on and and no chime is heard, repeat the reset procedure.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil light reset Jeep Renegade Concept

Many Jeep vehicles track the intervals between oil changes to alert the driver when the next oil change is needed. A light illuminates on the control panel when the internal system determines it is time for an oil change. Most Jeep mechanics reset the oil light as part of the oil change service. If you change the oil in your Jeep yourself, you can manually reset the oil light. Resetting the oil light after an oil change allows the system to accurately track the time until the next oil change is needed. The procedures described in this article apply to 2010 Jeep models.

Instructions

1.Turn the ignition switch to the “ON” position. Do not start the engine.

2.Press the accelerator pedal completely to the floor slowly three times within a 10-second span.

3.Turn the ignition switch to the “OFF” position.

4.Turn the ignition switch to the “ON” position again. The oil light should be off. If the oil light is still illuminated, repeat the previous steps.