Oil service reset NISSAN GT-R

2009-2011

1. Push the ignition switch to the ON position (do not start the engine). Use the ENTER button (?) and toggle the vehicle information display to show the SETTING screen. Use the NEXT button (?) to select.
2. Use the NEXT button (?) to select MAINTENANCE
i) SETTING > MAINTENANCE > OIL > ENGINE OIL to set or reset the mileage for the engine oil change.
ii) SETTING > MAINTENANCE > FILTER > to set or reset the mileage for the engine oil filter.
3. Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset GL – Class

2007-2012

1. Turn the ignition to position 1. (close all doors
2. Press the system selection button (3 located on the lower left of the steering wheel) repeatedly until the kilometer or temperature reading is shown in the multi information display.)
3. Press the TRIP reset button (center button on instrument panel) quickly 3 times. An audible beep will be heard followed by the battery voltage displayed.
4. Press the scoll forward/back button (left side of steering wheel) to highlight the “”Service menu””.”
5. Use the +/- buttons to select “”Confirmation”” menu. Press the system select button to confirm. The menu item “”Complete service”” is highlighted.”
6. Press the system selection button to confirm. “”Service confirmed”” appears.”
7. Use the scroll forward/back button to exit the menu.
8. Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset R – Class

2006-2012

1. Turn the ignition to position 1. (close all doors
2. Press the system selection button (3 located on the lower left of the steering wheel) repeatedly until the kilometer or temperature reading is shown in the multi information display.)
3. Press the TRIP reset button (center button on instrument panel) quickly 3 times. An audible beep will be heard followed by the battery voltage displayed.
4. Press the scoll forward/back button (left side of steering wheel) to highlight the “”Service menu””.”
5. Use the +/- buttons to select “”Confirmation”” menu. Press the system select button to confirm. The menu item “”Complete service”” is highlighted.”
6. Press the system selection button to confirm. “”Service confirmed”” appears.”
7. Use the scroll forward/back button to exit the menu.
8. Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset SLS – Class

2010-2012

1. Turn the ignition to position 1. (close all doors
2. Press the system selection button (left button on left steering wheel controls) repeatedly until the kilometer reading is shown in the multi information display.)
3. Press the system selection button (located on the far left of the steering wheel) repeatedly until the menu item “”trip”” with highlighter is stored in the multi-function display. *Trip remains selected for 5 seconds so you need to move to step 4.”
4. First press and hold the accept phone call button and within 1 second also press and hold the OK button for 5 seconds. The workshop menu will appear in the display showing “”vehicle data
5. Press the scroll forward button (lower button on left steering wheel controls) to highlight “”ASSYST PLUS”” and then confirm by pressing OK button.”
6. Press scroll forward button (lower button on left steering wheel controls) to highlight “”Full Service”” and then confirm by pressing OK button.”
7. Press scroll forward button until “”YES”” is highlighted and confirm swith OK button. “”No take-back possible”” appears.”
8. Press scroll forward button until “”Confirmation”” is highlighted and confirm with OK button. “”Full service carried out”” appears.”
9. Press OK button and back button (standalone button on left steering wheel controls) repeatedly until the menus are exited.
10. Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset SLK – Class

1998-1999
*Diagnostic Reset Tool Required
Manual Reset:

1. Turn key in steering lock to position 2.
2. Within 4 seconds press button (1) left of speedometer twice.
3. The present status for days or distance displays
4. Press and hold button (1)
5. Continue to hold button (1) for approximately 10 seconds until a signal sounds and the display shows 10 000 mils or 15 000km. Release button (1).
6. Turn the ignition off and then start the engine to verify the indicator has been reset.
2000-2001
*Diagnostic Reset Tool Required

Manual Reset:

1. Switch ignition on and immediately press knob to left of speedometer twice within 4 seconds.
2. Present status for days or distance is now displayed. Within 10 seconds
3. Press and hold button to the left of speedometer
4. Release button.
5. Service interval displays the reset interval.
6. Turn the ignition off and then start the engine to verify the indicator has been reset.

2002-2004
1. Switch ignition on and immediately press knob to left of speedometer twice within 1 second.
2. Present status for days or distance is now displayed. Within 10 seconds
3. Press and hold button to the left of speedometer
4. Release button.
5. Service interval displays the reset interval.
6. Turn the ignition off and then start the engine to verify the indicator has been reset.

2005-2009
1. Turn the ignition to position 1.
2. Press the system selection button (3 located on the lower left of the steering wheel) repeatedly until the kilometer reading is shown in the multi information display.)
3. Press the cluster illumination button (lower left of instrument panel) quickly 3 times. The battery voltage will be displayed.
4. Press the up or down buttons until the service menu appears.
5. Use the +/- buttons to select menu oprion “”CONFIRM””.”
6. Press the system selection button uuntil “”COMPLETE SERVICE”” is selected.”
7. Confirm “”Complete Service”” with system selection button. The display will show “”SERVICE CONFIRMED””.”
8. Turn the ignition off and then start the engine to verify the indicator has been reset.

2010-2012
1. Turn the ignition to position 1. (close all doors
2. Press the scroll forward button (bottom button on left side of steering wheel controls) to display mileage counter.
3. Press the system selection button (left button on left side of steering wheel controls) repeatedly until the menu item “”trip”” with highlighter is displayed. “”Trip”” remains selected for 5 seconds so move quickly to step 4.”
4. Press and hold accept/end phone button and within 1 second press and hold the button in the center of the arrows (left side of steering wheel). In 5 seconds the Workshop menu will be displayed “”Vehicle data
5. Use scroll forward or backward to highlight “”ASSYST PLUS”” and confirm selection using the button in the center of the arrows. “”Service data”” and “”Full service”” appear in the display.”
6. Use scroll forward or backward to select “”Full service”” and confirm selection with the button in the center of the arrows. The display will show “”Service 1
7. Use scroll forward or backward to select “”Confirm serv”” and confirm selection with the button in the center of the arrows.”
8. Use scroll forward or backward to select engine oil specification used. “”Oil qual. 229.3″” and “”Oil qual. 229.5″” are displayed. Confirm selection with center button. The display shows “”Serv conducted?”””
9. Use scroll forward or backward to select “”Yes”” and confirm with center button. Display will show “”Take-back not possible
10. Use scroll forward or backward until “”Configuration”” is highlighted and confirm selection with button in center of the arrows. “”Full service carried out”” appears in the display.”
11. Use scroll forward and backward to exit menu.
12. Turn the ignition off and then start the engine to verify the indicator has been reset.