There are 3 stages
locate the obd plug and find pin 8 then
turn ignition to pos 2
with a fused wire ( a piece of wire with a fuse in it)
ground pin 8 for 4-5 seconds
turn ignition off
repeat this procedure 2 more times but for 8-12 seconds and then the service indicator will be reset.
Tag: oil service indicator
Reset the service indicator light 2007 Renault clio
Turn on the ignition, but don’t start the car. On the right stalk there is a toggle switch that hinges up and down, and is used for going through the different features of the display. When the display shows ‘Service Due’ press and hold the top part of this switch for 10 seconds until the dispaly resets and it shows 30,000km or whatever until next service.
Turn on the ignition, but don’t start the car. On the right stalk there is a toggle switch that hinges up and down, and is used for going through the different features of the display. When the display shows ‘Service Due’ press and hold the top part of this switch for 10 seconds until the dispaly resets and it shows 30,000km or whatever until next service.
all of the above is correct apart from pressing the toggle button. if you instead press the bottom toggle button for 10 seconds the display will start to flash. Keep button depressed and 5 seconds later the service counter will reset.
Reset Service light for 2006 Volvo XC90
“Resetting the service reminder indicator (SRI), model years 2002-
The service reminder indicator (SRI) informs the driver that it is time for the car to be serviced. The text message is displayed for 120s each time the ignition is switched on.
Proceed as follows to reset the service reminder indicator (SRI):
1.Ignition position I
2. Press and hold in the reset button for the trip odometer
3. Ignition position II. Note! Turn the key to position II within 2 seconds
4. Hold the reset button for the trip meter pressed in until the original value has been reset. Note! For all vehicles from the 2003 model year a general yellow lamp will light when the reset button must be released
5. Release the reset button for the trip odometer within 4 seconds. The instrument gives an audible signal when resetting has succeeded
6. If the trip meter is already reset the reset button should be held in for a minimum of 10 seconds and a maximum of 14 seconds.
Note! If the reset button for the trip odometer is not released within 4 seconds, the service reminder indicator (SRI) is not reset.”
Reset maintenance light on dodge sprinter
1. Put the key in the ignition and switch it on without starting the engine.
(Wait for LCD to return to the vehicle mileage)
2. Hold the “O” button down till you hear a beep (could take a while, 30 sec.)
3. Press the M button repeatedly and a number of reset menus will appear, (If you have used oil according to quality sheet 229.31 or 228/229.51 you can scroll to Reset.31 or Reset.51 respectively.) Select “reset 51”
4. Now, when appropriate oil type is selected press “O” for 6 seconds until ”2” is displayed.
5. Press “O” once again briefly and the ” reset done” message will confirm that the job is done.
6. Pull the Key out
FOR THE 2004 DODGE SPRINTER!
Turn the key to position 2 in the ignition lock and immediately press the button MI (km) twice.
Within 10 seconds, return the key to the 0 in the ignition lock.
Press and hold the button MI (km). Turn the key to position 2 in the ignition lock. Keep the button MI (km) pressed.
The maintenance indicator with the time/distance is shown.
After about 10 seconds, an acoustic signal will sound and the maintenance indicator is displayed with the new remaining time / distance .
Release the button MI (km)
Reset service light Renault Twingo 2007
The service light on these vehicles is usually a spanner / wrench symbol. To reset that indicator:
Turn the Ignition ON (position 2) but do not start the engine
(On cars with keycard ignition, insert the card, then press and hold the start button for 5 seconds to turn on the dash cluster)
Press the button on the end of the wiper stalk repeatedly until the spanner symbol and miles to service appears on the display
(Some models have 2 buttons, which cycle through the options in opposite directions – either button can be used in this case)
Press and hold the button
The display will now change to the new service interval and start flashing
Keep holding the button until the display stops flashing
Release the button