Reset maintenance light on dodge sprinter

1. Put the key in the ignition and switch it on without starting the engine.
(Wait for LCD to return to the vehicle mileage)
2. Hold the “O” button down till you hear a beep (could take a while, 30 sec.)
3. Press the M button repeatedly and a number of reset menus will appear, (If you have used oil according to quality sheet 229.31 or 228/229.51 you can scroll to Reset.31 or Reset.51 respectively.) Select “reset 51”
4. Now, when appropriate oil type is selected press “O” for 6 seconds until ”2” is displayed.
5. Press “O” once again briefly and the ” reset done” message will confirm that the job is done.
6. Pull the Key out
FOR THE 2004 DODGE SPRINTER!

Turn the key to position 2 in the ignition lock and immediately press the button MI (km) twice.
Within 10 seconds, return the key to the 0 in the ignition lock.
Press and hold the button MI (km). Turn the key to position 2 in the ignition lock. Keep the button MI (km) pressed.
The maintenance indicator with the time/distance is shown.
After about 10 seconds, an acoustic signal will sound and the maintenance indicator is displayed with the new remaining time / distance .
Release the button MI (km)

Oil service reset Jeep Cherokee SRT8

On my ’08 I just had the oil change indicator come on, and I successfully reset it. The point is that the message took a few seconds after turning the key on to appear in the dash. You need to wait until the message appears, then you have 10 seconds to do the 3 pedal depresses. It doesn’t work if you start depressing the pedal immediately after turning the key on, if you don’t wait for the oil change message to appear.

Reset the service oil light on jaguar s-type

Here’s how to do it yourself in no time works on a few different Jags….

Service Light Reset Instructions:

1 . Insert key into ignition.
2 . Press and hold the Reset switch (located on the Trip Computer Switchpack ).
3 . NOTE: The reset switch has to be released immediately after the ignition is switched ‘ON’. This is critical to enable the rest of the procedure.
Turn the key to Ignition position II and at the point of entering Ignition position II (i.e when a click is heard), instantaneously release the Reset switch.
4 . Wait one second.
5 . Press and hold the Trip switch (located on the end of the left-hand side stalk).
6 . Wait one second.
7 . Press and hold the Reset switch (whilst still holding the Trip switch).
8 . The cluster should display (within three seconds) the warning message ‘RESETTING SERVICE MODE’.
9 . Keep both buttons pressed until the warning message changes to ‘SERVICE MODE RESET’ (after ten seconds).
10 . Once the message is displayed the buttons may be released — sequence is now complete.
11 . If a Service Required message was displayed prior to the reset sequence, cycle the ignition to ‘Off’ and then back to Ignition position II and check that the message is no longer displayed.

Oil service reset Chrysler Dodge Trucks Sprinter

2004-2005

Turn the key to position 2 in the ignition lock and immediately press the MI (MILES)button twice.
Within 10 seconds, return the key to position 0 in the ignition lock.
Press and hold the button (MI). Turn the key to position 2 in the ignition lock. Keep the button (MI) pressed.
The maintenance indicator with the current remaining time/distance is shown. After about 10 seconds, an acoustic signal will sound and the maintenance indicator is displayed with the new remaining time/distance. Release the button MI(KM).
Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset Chrysler Dodge Crossfire

2004-2008

Turn the ignition to run (one position before starting engine).
Within one second press the knob/button twice.
The present status for days or distance is displayed. Within 10 seconds turn the key to OFF/LOCK.
Press and hold the knob/button, while turning the distance is displayed once more. Continue to hold the knob/button. After 10 seconds, a signal sounds and the display shows 7,000 mi or 11000km for 10 seconds.
Release the knob/button.
Turn the ignition off and then start the engine to verify the indicator has been reset.