Oil service reset SLK – Class

1998-1999
*Diagnostic Reset Tool Required
Manual Reset:

1. Turn key in steering lock to position 2.
2. Within 4 seconds press button (1) left of speedometer twice.
3. The present status for days or distance displays
4. Press and hold button (1)
5. Continue to hold button (1) for approximately 10 seconds until a signal sounds and the display shows 10 000 mils or 15 000km. Release button (1).
6. Turn the ignition off and then start the engine to verify the indicator has been reset.
2000-2001
*Diagnostic Reset Tool Required

Manual Reset:

1. Switch ignition on and immediately press knob to left of speedometer twice within 4 seconds.
2. Present status for days or distance is now displayed. Within 10 seconds
3. Press and hold button to the left of speedometer
4. Release button.
5. Service interval displays the reset interval.
6. Turn the ignition off and then start the engine to verify the indicator has been reset.

2002-2004
1. Switch ignition on and immediately press knob to left of speedometer twice within 1 second.
2. Present status for days or distance is now displayed. Within 10 seconds
3. Press and hold button to the left of speedometer
4. Release button.
5. Service interval displays the reset interval.
6. Turn the ignition off and then start the engine to verify the indicator has been reset.

2005-2009
1. Turn the ignition to position 1.
2. Press the system selection button (3 located on the lower left of the steering wheel) repeatedly until the kilometer reading is shown in the multi information display.)
3. Press the cluster illumination button (lower left of instrument panel) quickly 3 times. The battery voltage will be displayed.
4. Press the up or down buttons until the service menu appears.
5. Use the +/- buttons to select menu oprion “”CONFIRM””.”
6. Press the system selection button uuntil “”COMPLETE SERVICE”” is selected.”
7. Confirm “”Complete Service”” with system selection button. The display will show “”SERVICE CONFIRMED””.”
8. Turn the ignition off and then start the engine to verify the indicator has been reset.

2010-2012
1. Turn the ignition to position 1. (close all doors
2. Press the scroll forward button (bottom button on left side of steering wheel controls) to display mileage counter.
3. Press the system selection button (left button on left side of steering wheel controls) repeatedly until the menu item “”trip”” with highlighter is displayed. “”Trip”” remains selected for 5 seconds so move quickly to step 4.”
4. Press and hold accept/end phone button and within 1 second press and hold the button in the center of the arrows (left side of steering wheel). In 5 seconds the Workshop menu will be displayed “”Vehicle data
5. Use scroll forward or backward to highlight “”ASSYST PLUS”” and confirm selection using the button in the center of the arrows. “”Service data”” and “”Full service”” appear in the display.”
6. Use scroll forward or backward to select “”Full service”” and confirm selection with the button in the center of the arrows. The display will show “”Service 1
7. Use scroll forward or backward to select “”Confirm serv”” and confirm selection with the button in the center of the arrows.”
8. Use scroll forward or backward to select engine oil specification used. “”Oil qual. 229.3″” and “”Oil qual. 229.5″” are displayed. Confirm selection with center button. The display shows “”Serv conducted?”””
9. Use scroll forward or backward to select “”Yes”” and confirm with center button. Display will show “”Take-back not possible
10. Use scroll forward or backward until “”Configuration”” is highlighted and confirm selection with button in center of the arrows. “”Full service carried out”” appears in the display.”
11. Use scroll forward and backward to exit menu.
12. Turn the ignition off and then start the engine to verify the indicator has been reset.

RESET SERVICE INDICATOR SEAT AROSA

Hot to reset service light on a Seat Arosa

The SEAT owners manual for the Arosa states.

With the ignition switched off, press and hold the trip meter reset button below the speedometer.

Then, switch the ignition on and hold the reset button for atleast 10 sconds.

Dashes will then appear in the display.

The service has been reset.

Reset oil service Toyota

Toyota 4Runner 2003-onwards

With the ignition “OFF”, press and hold “RESET” button. Turn ignition to the “ON” position. Continue to hold button until “MAINT REQD” light turns off.
Turn ignition off.

Camry 2004-onwards
With the ignition “OFF”, press and hold button below the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.

Corolla

Turn the key to the off position. Press and hold down the trip meter button and turn the key to the “on” position. Continue to hold the trip button for 5 seconds after the key is turned on, then release.

Highlander 2004-onwards
With the ignition “OFF”, press and hold button below the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.

Matrix 2004-onwards
With the ignition “OFF”, press and hold button below the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.

Prius 2004-onwards
With the “POWER” switch off, press and hold “ODO TRIP” button. Press “POWER” switch twice selecting “IG-ON”. Continue to hold button until”000000″ is displayed and “MAINT REQD” light turns off. Turn “POWER” switch to off.

RAV4 2004-onwards
With the ignition “OFF”, press and hold button below the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.

Sequoia 2004-onwards
With the ignition “OFF”, press and hold button below the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.

Sienna 2004-onwards
With the ignition “OFF”, press and hold button to the right of the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″
is displayed and the “MAINT REQD” lamp turns off. Turn ignition off.

Solara 2004-onwards
With the ignition “OFF”, press and hold button to the left of the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.

Tacoma 2005-onwards
With the ignition “OFF”, press and hold button to the right of the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″
is displayed and the “MAINT REQD” lamp turns off. Turn ignition off.

Tundra 2003-onwards
With the ignition “OFF”, press and hold button below the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.

Oil service reset Volkswagen Jetta

1993-1999
Turn the ignition to run (one position before starting engine).
Press and hold the button located under the speedometer.
Switch ignition off and release button. Message OIL appears in the display.
Press MINUTE button of digital clock or button for setting analog clock only as long as 5 dashes appears in display.
Turn the ignition off and then start the engine to verify the indicator has been reset.

2000-2004

Reset may be similar to previous year or other models – Oil Reset will verify and update site.

2005-2010

Manual Reset:
Turn the ignition to run (one position before starting engine).
Press and HOLD the trip-odometer button “0.0”.
Turn your key to run (one position before starting engine).
Release the trip-odometer button.
Push and release the Clock Minute Set Button “min”.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset Volkswagen Cabrio

1995-2002

Turn the ignition to run (one position before starting engine).
Press and hold the button located under the speedometer.
Switch ignition off and release button. Message OIL appears in the display.
Press MINUTE button of digital clock or button for setting analog clock only as long as 5 dashes appears in display.
Turn the ignition off and then start the engine to verify the indicator has been reset.