Tag: vehicle

Service reset for 2007 Fiat Ducato

Switch Ign on (do not start engine)
Set Odometer to read total miles.
Press Odometer Button (OB) until CFG1 appears in display
Release the OB.
Pressing the OB briefly will change between CFG1, CFG2, CFG3, CFG1
Once you have selected the CFG (see below).
Press the OB again for 5secs to store the new service frequency.
Turn off the ignition.

I selected CFG1 for my vehicle (05 Reg 2.8JTD), but you must decide yourself for your vehicle, should take 5mins to read this and carry out the resetting procedure

Note: If your vehicle is under warranty and you take it to be serviced by a Fiat dealer they will do this as part of the service.

CFG1 = 30000km (18,600mi) and 365 days in cases of Standard Use for 2.0 petrol and 2.8JTD versions, or in the case of Severe Use for the 2.3JTD versions.

CFG2 = 20000km (12,500mi) and 365 days in case of Standard Use for 2.0JTD versions, or in case of severe use for 2.0 petrol and 2.8JTD versions

CFG3 = 15000km (9,300mi) and 365 days in case of Severe Use for 2.0JTD versions

Turn Off an Oil Light on a 2005 KIA Spectra

Instructions

1. Pull the vehicle over to a safe area, if the light comes on while driving. If you are very close to a store that sells motor oil, stop there. Do not continue driving with the indicator light lit, as severe engine damage may occur.

2. Turn off the vehicle’s engine and open the hood. Locate the oil filler cap and oil dipstick on the top-front of the engine.

3. Check the engine oil level on the oil dipstick. If the engine oil is low, remove the oil cap and add oil until the oil level on the oil dipstick reaches the “Full” mark.

4. Replace the oil cap and restart the Kia. The oil light should turn off within a few seconds of starting the vehicle.

Bentley Continental Fluying Spur service display reset 2004 –

The real repair is to have the vehicle serviced by a Bentley dealer. The other option is as follows…
Press and hold the trip button
While doing this, turn the ignition key into the on position
Let go of both, and you will see the words “service reset” on the drivers instrument panel screen
Now press the silver knurled roller switch “OK” on the right side of the steering wheel controls, by the menu button. This will confirm the request.

Reset maintenance light on dodge sprinter

1. Put the key in the ignition and switch it on without starting the engine.
(Wait for LCD to return to the vehicle mileage)
2. Hold the “O” button down till you hear a beep (could take a while, 30 sec.)
3. Press the M button repeatedly and a number of reset menus will appear, (If you have used oil according to quality sheet 229.31 or 228/229.51 you can scroll to Reset.31 or Reset.51 respectively.) Select “reset 51”
4. Now, when appropriate oil type is selected press “O” for 6 seconds until ”2” is displayed.
5. Press “O” once again briefly and the ” reset done” message will confirm that the job is done.
6. Pull the Key out
FOR THE 2004 DODGE SPRINTER!

Turn the key to position 2 in the ignition lock and immediately press the button MI (km) twice.
Within 10 seconds, return the key to the 0 in the ignition lock.
Press and hold the button MI (km). Turn the key to position 2 in the ignition lock. Keep the button MI (km) pressed.
The maintenance indicator with the time/distance is shown.
After about 10 seconds, an acoustic signal will sound and the maintenance indicator is displayed with the new remaining time / distance .
Release the button MI (km)

Reset oil maintenance light on 2007 ford explorer

The directions that come with your vehicle are lousy, and the process stinks to. And keep in mind that if you do not press the buttons fast enough, or hold long enough, you must start over. It usually takes a few tries. Here’s how to do it:

1.) Press the TRIP/RESET button to cycle to “SETUP MENU HOLD RESET”.
2.) Now press and hold the button for 2 seconds until “RESET FOR SYSTEM CHECK” is displayed, then release.
3.) Imediately press and hold button for 2 more seconds until “Oil 100% RESET IF NEW” is displayed, then release.
4.) Imediately press button once to display “HOLD RESET IF NEW OIL” and release.
5.) Imediately press and hold button for 2 seconds until “OIL LIFE SET TO 100%” is displayed.

If you have done this dance properly, without delaying too long between steps, you are done. What a pain in the butt just to reset the oil maintenance light!!!