Tag: vehicle

Oil service reset Jeep Commander

Engine Oil Change Indicator System

Oil Change Required
Your vehicle is equipped with an engine oil change
indicator system. The “Oil Change Required” message
will flash in the EVIC display for approximately 10
seconds after a single chime has sounded to indicate the
next scheduled oil change interval. The engine oil change
indicator system is duty cycle based, which means the
engine oil change interval may fluctuate dependent upon
your personal driving style.
Unless reset, this message will continue to display each
time you turn the ignition switch to the ON/RUN
position. To turn off the message temporarily, press and
release the MENU button. To reset the oil change indicator
system (after performing the scheduled maintenance)
refer to the following procedure.

1. Turn the ignition switch to the ON position (Do not
start the engine).

2. Fully depress the accelerator pedal slowly three times
within 10 seconds.

3. Turn the ignition switch to the OFF/LOCK position.

NOTE: If the indicator message illuminates when you
start the vehicle, the oil change indicator system did not
reset. If necessary repeat this procedure.

Oil service reset Saturn Outlook

2007-2009

If your vehicle does not have Driver Information Center (DIC) buttons:
Turn the ignition to run (one position before starting engine).
Press the trip odometer reset stem until OIL LIFE REMAINING displays.
Press and hold the trip odometer reset stem until OIL LIFE REMAINING shows 100%. You will hear 3 chimes and the CHANGE ENGINE OIL SOON message will go off.
Turn the ignition off and then start the engine to verify the indicator has been reset.

If your vehicle has Driver Information Center (DIC) buttons:
Turn the ignition to run (one position before starting engine).
Press the vehicle information button (square) until OIL LIFE REMAINING displays.
Press and hold the set/reset button (arrow) until 100% is displayed. You will hear 3 chimes and the CHANGE ENGINE OIL SOON message will go off.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset Pontiac Grand Prix

1996-1997

Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds. If the CHANGE OIL SOON indicator flashes 2 times, the system is reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.

1998-2004

With Driver Information Centre:
Turn the ignition to run (one position before starting engine).
Press the trip calculator MODE button until the light appears next to OIL LIFE.
Press and hold the trip calculator RESET button until the oil life percentage changes to 100%.
Turn the ignition off and then start the engine to verify the indicator has been reset.
Without Driver Information Centre:
Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds. If the CHANGE OIL SOON indicator flashes 2 times, the system is reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.

2005-2010

Turn the ignition to run (one position before starting engine).
Press the OPTIONS button on the Driver Information Centre until ENGINE OIL MONITOR appears on DIC screen.
Press the SET/RESET button to reset the system. The next screen indicates that the engine oil monitor system has been reset. If the vehicle is equipped with the trip computer DIC, when the GAUGE button is pressed and the OIL LIFE REMAINING mode appears, it should read 100% OIL LIFE REMAINING appears, it should read 100 percent OIL LIFE REMAINING.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset Chevrolet GMC Trucks Suburban/Tahoe/Yukon

2000-2006

Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds.
If the Change Oil Soon light flashes the system is resetting.
Turn the ignition off and then start the engine to verify the indicator has been reset.

2007-2010

Turn the ignition to run (one position before starting engine).
Display the OIL LIFE REMAINING on the DIC (i button). If the vehicle does not have DIC buttons, the vehicle must be in P (Park) to access this display by pressing the trip odometer reset stem.
Press and hold the SET/RESET (check mark) button on the DIC , or the trip odometer reset stem if vehicle does not have DIC buttons for more than 5 seconds. The oil life will change to 100%.
Turn the ignition off and then start the engine to verify the indicator has been reset.

or

Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds.
Display the OIL LIFE REMAINING on the DIC. If the display shows 100%, the system is reset. If the vehicle has a CHANGE OIL SOON message this should be off.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset Chevrolet GMC Trucks Terrain

2010

With Driver Information Centre (DIC):
Turn the ignition to run (one position before starting engine).
Press the MENU button until vehicle information menu is displayed then scroll through the menu with the down arrow until Remaining Oil Life is selected then press SET/CLR (check button) to select.
Use up or down arrow to select YES to reset.
Confirm reset by pressing SET/CLR button.
Turn the ignition off and then start the engine to verify the indicator has been reset.
Without Driver Information Centre (DIC):
Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds.
If the Change Engine Oil Soon message goes off the system is reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.