Tag: oil

BMW X5 2002 Oil Reset

BMW X5 Engine Oil Service reset

Turn the ignition to “0”
Press and hold odometer button and turn the ignition to “1”.
Hold odometer button pressed for approximately 5 seconds until the display shows: “Inspektion Re /
Release and press odometer button again until Reset flashes
Release and press odometer button shortly.
Release and press odometer button again.
The next oil service interval will be shown and will disappear.
Oil service lamp is now reset

Note: To abort the procedure at any time: turn the ignition to “0”.

Rover 75 Reset Oil Service Light

Well after a small but required service on the car I had to reset the warning light. The real quick deal to reset all the requested lights on Rover 75 is to do the following

Get a small wire, Turn the key to second position, Short Pin 8 and Pin 4 on the OBD connector for “4 seconds to reset oil light”, “8-25 seconds for the other 2 lights” and this will reset the 15000 service request for oil change. Quick and easy and not legal if you do it without actually doing the service.

Reset oil change light on a 2008 dodge nitro

1. Turn the ignition key to ON but do not start the engine.
2. Slowly depress the accelerator to the floor and release it three times within 10 seconds.
3. Turn the ignition key to the OFF position.

Reset maintenance light on dodge sprinter

1. Put the key in the ignition and switch it on without starting the engine.
(Wait for LCD to return to the vehicle mileage)
2. Hold the “O” button down till you hear a beep (could take a while, 30 sec.)
3. Press the M button repeatedly and a number of reset menus will appear, (If you have used oil according to quality sheet 229.31 or 228/229.51 you can scroll to Reset.31 or Reset.51 respectively.) Select “reset 51”
4. Now, when appropriate oil type is selected press “O” for 6 seconds until ”2” is displayed.
5. Press “O” once again briefly and the ” reset done” message will confirm that the job is done.
6. Pull the Key out
FOR THE 2004 DODGE SPRINTER!

Turn the key to position 2 in the ignition lock and immediately press the button MI (km) twice.
Within 10 seconds, return the key to the 0 in the ignition lock.
Press and hold the button MI (km). Turn the key to position 2 in the ignition lock. Keep the button MI (km) pressed.
The maintenance indicator with the time/distance is shown.
After about 10 seconds, an acoustic signal will sound and the maintenance indicator is displayed with the new remaining time / distance .
Release the button MI (km)

Oil service reset Tornado

1986-1988

Turn the ignition to run (one position before starting engine).
The oil life index may be reset by pressing and holding the ENGINE DATA and GAGE buttons until Oil Index 100 message appears in the information display panel.
Turn the ignition off and then start the engine to verify the indicator has been reset.

1989

Turn the ignition to run (one position before starting engine).
Press ENG DATA until oil life index is displayed.
Press ENG DATA and GAGE simultaneously until oil life index resets to 100.
Turn the ignition off and then start the engine to verify the indicator has been reset.

1990

Turn the ignition to run (one position before starting engine).
Press ENG DATA until oil life index is displayed.
Press RESET/ENTER until oil life index resets to 100.
Turn the ignition off and then start the engine to verify the indicator has been reset.

1991-1992

Without Visual Information Centre:
Turn the ignition to run (one position before starting engine).
Press OPTIONS until oil life index is displayed.
Press RESET/ENTER until oil life index resets to 100 (hold about 5 seconds).
Turn the ignition off and then start the engine to verify the indicator has been reset.
With Visual Information Centre:
Turn the ignition to run (one position before starting engine).
Press INFO key then OIL LIFE key to display oil life index.
Press RESET key until oil life index resets to 100.
Turn the ignition off and then start the engine to verify the indicator has been reset.