Tag: engine oil

Service oil reset Nissan Pathfinder

2006-2007
Turn the ignition to run (one position before starting engine).
When you turn the ignition key run, the system start-up warning is displayed on the screen. Read the the warning and select the OK key by pressing the ENTER button.
When the TRIP button is pressed, the following modes will display on the screen: Warning message (if any) TRIP1 > TRIP 2 > FUEL ECONOMY > MAINTENANCE > AUDIO OR OFF > TRIP 1
Select MAINTENANCE and then select the Engine Oil key using the joystick and press the ENTER button to display the screen to change the maintenance interval/RESET.
To return to the previous display after the MAINTENANCE NOTICE screen is displayed, press the BACK button.
Turn the ignition off and then start the engine to verify the indicator has been reset.

2008-2010
Turn the ignition to run (one position before starting engine).
Press the INFO button and select the Maintenance Key using the NISSAN controller; the maintenance information will be displayed on the screen.
Select one of the Reminder (1 – 4) keys using the NISSAN controller and press the ENTER button to display the screen to change the maintenance interval.
To reset the reminder schedule (distance) to 0 mi (km), select the Reset Distance key using the NISSAN contoller.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Service oil reset Nissan Murano

2006-2008
Turn the ignition to run (one position before starting engine).
Maintenance and tire pressure information will be displayed when the “MAINT” button is pushed on the centre console.
To display the setting of the maintenance interval, select the “Engine Oil” key using the joystick and push the “ENTER” button.
To reset the maintenance interval, select the “Reset” key using the joystick and push the “ENTER” button.
Turn the ignition off and then start the engine to verify the indicator has been reset.

2009-2010
Turn the ignition to run (push START/STOP button once).
Switches for the trip computer are located on the right side of the combination meter panel. When the ignition switch is pushed to the ON position press the (square) button to bring up “Setting” and and press (circle) button to select.
Use the (circle) button to scroll to MAINTENANCE and use the (square) button to select.
Select ENGINE OIL to set or reset the distance for changing the oil.
Repeat step 2 to set or reset the distance for the OIL FILTER.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Service oil reset Lexus LX – Series

2005-2006
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the ODO/TRIP knob then the turn ignition off.
Hold down ODO/TRIP knob while turning the ignition key to the run position (one position before starting engine).
Hold down the knob until the light goes off. Before the light goes off, it illuminates
3 seconds, flashes for 2 seconds and illuminates for 1 second. If the system fails to reset, the light will remain flashing. In this case, return to step 1 and try again.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2007
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the ODO/TRIP knob then the turn ignition off.
Hold down ODO/TRIP knob while turning the ignition key to the run position (one position before starting engine) for longer than 7 seconds. While doing this operation, the “engine oil replacement” reminder light goes off. If the system fails to reset, the light will remain flashing. In this case, return to step 1 and try again.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2008-2010
Turn the engine on by holding the START/STOP switch. Use the trip meter switch to bring up the trip meter A reading. Turn the ignition off.
While pressing the trip meter reset button, set the engine switch to run (push START/ STOP button once) and continue to press and hold the knob until the multi information display indicates that the reset is complete.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Service oil reset Infiniti QX56

2004-2007
Turn the ignition to run (one position before starting engine).
Push the ěTRIPî button repeatedly to display “MAINTENANCE” and press the “ENTER” button.
Select “Engine Oil” and press the “ENTER” button.
Select “RESET” and press “ENTER” button.
Press “PREV” to return to previous menu.
Turn the ignition off and then start the engine to verify the indicator has been reset.

2008-2010
Turn the ignition on without starting the engine (press START/STOP) button.
Push the ěINFOî button on the control panel for the Vehicle Information screen.
Use arrow keys to scroll down to “Maintenance” and press “ENTER” button to select.
Select “Reminder 1” and press “ENTER” button.
Select “Reset Distance” and press “ENTER” button.
Press “Back” button to return to “Maintenance” menu and repeat procedure for “Reminder 2″… Turn the ignition off and then start the engine to verify the indicator has been reset.

Service oil reset Infiniti M Series

2003-2004
Turn the ignition to run (one position before starting engine).
Push the “INFO” button on the control panel for the Vehicle Information screen.
Choose “Maintenance” using the joystick and push the “ENTER” button.
Select “Engine Oil” and press “ENTER” button.
Select “Reset” and press “ENTER” button.
Press “PREV” button to return to “Maintenance” menu and repeat procedure for “Oil Filter”. Turn the ignition off and then start the engine to verify the indicator has been reset.
2006-2007
Turn the ignition to run (one position before starting engine).
Push the “INFO” button on the control panel for the Vehicle Information screen.
Use arrow keys to scroll down to “Maintenance” and press “ENTER” button to select.
Select “Engine Oil” and press “ENTER” button.
Select “Reset Distance” and press “ENTER” button.
Press “BACK” button to return to “Maintenance” menu and repeat procedure for “Oil Filter”. Turn the ignition off and then start the engine to verify the indicator has been reset.
2008-2010
Turn the ignition on without starting the engine (press START/STOP) button.
Push the “INFO” button on the control panel for the Vehicle Information screen.
Use arrow keys to scroll down to “Maintenance” and press “ENTER” button to select.
Select “Reminder 1” and press “ENTER” button.
Select “Reset Distance” and press “ENTER” button.
Press “Back” button to return to “Maintenance” menu and repeat procedure for “Reminder 2″… Turn the ignition off and then start the engine to verify the indicator has been reset.