Tag: trip computer

Renault Scenic service indicator light reset

To reset the service indicator on the scenic II is as follows:
Scroll through the trip computer using the button on the end of the right hand stalk control until you get to the miles till service indicator (or the “change oil soon message” will appear if due)
Then press and hold the same button in and hold it. The miles indicator will then flash then change to 18000, keep the button pressed until the 18000 stops flashing.

NOTE: If the word “service” appears on your dash then that does NOT mean that a service is due. It is an indication that the vehicle is faulty and has a stored major fault code.

The indicator that a Service is due is when the words “change oil soon” appears or the spanner starts flashing.

Service light on my Renault Megane Scenic

The procedure for the Mégane II (2002-2006, pre-facelift model) is:

Scroll through the trip computer until you get to the “change oil soon message/miles to next service” displayed.
Press and hold the mileage trip reset button on the speedo untill the display flashes, and then stays fixed. This can take a few seconds.

Reset the service oil light on jaguar s-type

Here’s how to do it yourself in no time works on a few different Jags….

Service Light Reset Instructions:

1 . Insert key into ignition.
2 . Press and hold the Reset switch (located on the Trip Computer Switchpack ).
3 . NOTE: The reset switch has to be released immediately after the ignition is switched ‘ON’. This is critical to enable the rest of the procedure.
Turn the key to Ignition position II and at the point of entering Ignition position II (i.e when a click is heard), instantaneously release the Reset switch.
4 . Wait one second.
5 . Press and hold the Trip switch (located on the end of the left-hand side stalk).
6 . Wait one second.
7 . Press and hold the Reset switch (whilst still holding the Trip switch).
8 . The cluster should display (within three seconds) the warning message ‘RESETTING SERVICE MODE’.
9 . Keep both buttons pressed until the warning message changes to ‘SERVICE MODE RESET’ (after ten seconds).
10 . Once the message is displayed the buttons may be released — sequence is now complete.
11 . If a Service Required message was displayed prior to the reset sequence, cycle the ignition to ‘Off’ and then back to Ignition position II and check that the message is no longer displayed.

Oil service reset Pontiac Grand Prix

1996-1997

Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds. If the CHANGE OIL SOON indicator flashes 2 times, the system is reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.

1998-2004

With Driver Information Centre:
Turn the ignition to run (one position before starting engine).
Press the trip calculator MODE button until the light appears next to OIL LIFE.
Press and hold the trip calculator RESET button until the oil life percentage changes to 100%.
Turn the ignition off and then start the engine to verify the indicator has been reset.
Without Driver Information Centre:
Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds. If the CHANGE OIL SOON indicator flashes 2 times, the system is reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.

2005-2010

Turn the ignition to run (one position before starting engine).
Press the OPTIONS button on the Driver Information Centre until ENGINE OIL MONITOR appears on DIC screen.
Press the SET/RESET button to reset the system. The next screen indicates that the engine oil monitor system has been reset. If the vehicle is equipped with the trip computer DIC, when the GAUGE button is pressed and the OIL LIFE REMAINING mode appears, it should read 100% OIL LIFE REMAINING appears, it should read 100 percent OIL LIFE REMAINING.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Service oil reset Nissan Murano

2006-2008
Turn the ignition to run (one position before starting engine).
Maintenance and tire pressure information will be displayed when the “MAINT” button is pushed on the centre console.
To display the setting of the maintenance interval, select the “Engine Oil” key using the joystick and push the “ENTER” button.
To reset the maintenance interval, select the “Reset” key using the joystick and push the “ENTER” button.
Turn the ignition off and then start the engine to verify the indicator has been reset.

2009-2010
Turn the ignition to run (push START/STOP button once).
Switches for the trip computer are located on the right side of the combination meter panel. When the ignition switch is pushed to the ON position press the (square) button to bring up “Setting” and and press (circle) button to select.
Use the (circle) button to scroll to MAINTENANCE and use the (square) button to select.
Select ENGINE OIL to set or reset the distance for changing the oil.
Repeat step 2 to set or reset the distance for the OIL FILTER.
Turn the ignition off and then start the engine to verify the indicator has been reset.