1997-2000
*Diagnostic Reset Tool Required (please refer to TOOLS page)
Manual Reset:
Turn key in steering lock to position 2.
Within 4 seconds press 0 button twice.
The present status for days or distance displays, within 10 seconds turn the electroninc key in steering lock to position 0.
Press and hold 0 button while turning electronic key in steering loack to position 2 again. The present status for days or distance displays once more. Continue to hold 0 button for approximately 10 seconds until a signal sounds and the display shows 10 000 (15000KM) for approximately 10 seconds.
Release 0 button, the status is reset.
2001
Turn key in steering lock to position 2.
Call up the trip odometer and main odometer: press either of the lower two buttons on the left hand side of steering wheel until the display appears.
Press either of the top buttons on steering wheel (arrows) until the FSS indicator appears.
Press R button on the instrument cluster for 2-4 seconds.
The display reads “DO YOU WANT TO RESET SERVICE INTERVAL?” confirm by pressing R button.
Press and hold the R button on instrument cluster again until signal sounds. Message will res “SERVICE INTERVAL HAS BEEN RESET”.
2002
Switch ignition on.
Repeatedly press the system selection button (bottom button located on left hand side of steering wheel) until the service symbol is displayed in the multifunction display.
Repeatedly press the SCROLL FORWARD/BACK button (top button on left hand side of steering wheel) until the service symbol is displayed in the multifunction display.
“DO YOU WANT TO RESET THE SERVICE INTERVAL?” appears, confirm that you see the message by holding down the RESET (R) button until you hear a signal.
The reset interval is set.
2003
Turn on the ignition (standard display of the control system appears).
Press SYSTEM button on the multifunction steering wheel until FSS indicator with service symbol and the service deadline appear on display.
Message appears on display “DO YOU WANT TO RESET THE SERVICE INTERVAL?” Confirm by pressing RESET (R) button until you hear a signal (approximately 4 seconds).
2004
Turn on the ignition (standard display of the control system appears).
Press button (UP arrow) or (DOWN arrow) on the multifunction steering wheel until the FSS indicator appears in the display.
Press RESET button for about 3 seconds until this message appears: “SERVICE INTERVAL? RESET WITH R BUTTON FOR 3 SEC.”
To confirm press RESET button until you hear a signal. The service indicator now displays the reset interval.
Tag: back
Service oil reset Nissan Z
2006-2008
Turn the ignition to run (one position before starting engine).
When you turn the ignition key run, the system start-up warning is displayed on the screen. Read the the warning and select the OK key by pressing the ENTER button.
When the TRIP button is pressed, the following modes will display on the screen: Warning message (if any) TRIP1 > TRIP 2 > FUEL ECONOMY > MAINTENANCE > AUDIO OR OFF > TRIP 1
Select MAINTENANCE and then select the Engine Oil key using the joystick and press the ENTER button to display the screen to change the maintenance interval/RESET.
To return to the previous display after the MAINTENANCE NOTICE screen is displayed, press the BACK button.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2009-2010
Turn the ignition to run (push START/STOP button once).
Press the (square) button, located on the instrument panel just behind the steering wheel to the left, to display the SETTINGS mode.
In the setting mode screen press (circle) button to move to MAINTENANCE.
Set a desired interval by pushing (circle) button to highlight ENGINE OIL and pressing (square) button The reset mode will open up and allow you to enter the desired distance.
Select RESET and select new time or distance.
Repeat step 3 for ENGINE OIL FILTER. Turn the ignition off and then start the engine to verify the indicator has been reset.
Service oil reset Nissan Titan
2006-2010
Turn the ignition to run (one position before starting engine).
When the TRIP button is pressed, the following modes will display on the screen: Warning message (if any) TRIP1 > TRIP 2 > FUEL ECONOMY > MAINTENANCE > AUDIO OR OFF > TRIP
Select MAINTENANCE and then select the Engine Oil key using the joystick and press the ENTER button to display the screen to change the maintenance interval/RESET.
To return to the previous display after the MAINTENANCE NOTICE screen is displayed, press the BACK button.
Turn the ignition off and then start the engine to verify the indicator has been reset.
Service oil reset Nissan Quest
2006-2009
Turn the ignition to run (one position before starting engine).
When the TRIP button is pressed, the following modes will display on the screen: Warning message (if any) TRIP1 > TRIP 2 > FUEL ECONOMY > MAINTENANCE > AUDIO OR OFF > TRIP
Select MAINTENANCE and then select the Engine Oil key using the joystick and press the ENTER button to display the screen to change the maintenance interval/RESET.
To return to the previous display after the MAINTENANCE NOTICE screen is displayed, press the BACK button.
Turn the ignition off and then start the engine to verify the indicator has been reset.
Service oil reset Nissan Pathfinder
2006-2007
Turn the ignition to run (one position before starting engine).
When you turn the ignition key run, the system start-up warning is displayed on the screen. Read the the warning and select the OK key by pressing the ENTER button.
When the TRIP button is pressed, the following modes will display on the screen: Warning message (if any) TRIP1 > TRIP 2 > FUEL ECONOMY > MAINTENANCE > AUDIO OR OFF > TRIP 1
Select MAINTENANCE and then select the Engine Oil key using the joystick and press the ENTER button to display the screen to change the maintenance interval/RESET.
To return to the previous display after the MAINTENANCE NOTICE screen is displayed, press the BACK button.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2008-2010
Turn the ignition to run (one position before starting engine).
Press the INFO button and select the Maintenance Key using the NISSAN controller; the maintenance information will be displayed on the screen.
Select one of the Reminder (1 – 4) keys using the NISSAN controller and press the ENTER button to display the screen to change the maintenance interval.
To reset the reminder schedule (distance) to 0 mi (km), select the Reset Distance key using the NISSAN contoller.
Turn the ignition off and then start the engine to verify the indicator has been reset.