Oil service reset Jeep Commander

Engine Oil Change Indicator System

Oil Change Required
Your vehicle is equipped with an engine oil change
indicator system. The “Oil Change Required” message
will flash in the EVIC display for approximately 10
seconds after a single chime has sounded to indicate the
next scheduled oil change interval. The engine oil change
indicator system is duty cycle based, which means the
engine oil change interval may fluctuate dependent upon
your personal driving style.
Unless reset, this message will continue to display each
time you turn the ignition switch to the ON/RUN
position. To turn off the message temporarily, press and
release the MENU button. To reset the oil change indicator
system (after performing the scheduled maintenance)
refer to the following procedure.

1. Turn the ignition switch to the ON position (Do not
start the engine).

2. Fully depress the accelerator pedal slowly three times
within 10 seconds.

3. Turn the ignition switch to the OFF/LOCK position.

NOTE: If the indicator message illuminates when you
start the vehicle, the oil change indicator system did not
reset. If necessary repeat this procedure.

Reset the service oil light on jaguar s-type

Here’s how to do it yourself in no time works on a few different Jags….

Service Light Reset Instructions:

1 . Insert key into ignition.
2 . Press and hold the Reset switch (located on the Trip Computer Switchpack ).
3 . NOTE: The reset switch has to be released immediately after the ignition is switched ‘ON’. This is critical to enable the rest of the procedure.
Turn the key to Ignition position II and at the point of entering Ignition position II (i.e when a click is heard), instantaneously release the Reset switch.
4 . Wait one second.
5 . Press and hold the Trip switch (located on the end of the left-hand side stalk).
6 . Wait one second.
7 . Press and hold the Reset switch (whilst still holding the Trip switch).
8 . The cluster should display (within three seconds) the warning message ‘RESETTING SERVICE MODE’.
9 . Keep both buttons pressed until the warning message changes to ‘SERVICE MODE RESET’ (after ten seconds).
10 . Once the message is displayed the buttons may be released — sequence is now complete.
11 . If a Service Required message was displayed prior to the reset sequence, cycle the ignition to ‘Off’ and then back to Ignition position II and check that the message is no longer displayed.

Service oil reset Mercedes Benz S – Class

1997-1999
*Diagnostic Reset Tool Required
Turn key in steering lock to position 2.
Within 4 seconds press button (1) left of speedometer twice.
The present status for days or distance displays, within 10 seconds turn key in steering lock to position 0.
Press and hold button (1), while turning key in steering lock to position 2 again. The present status for days or distance displays once more.
Continue to hold button (1) for approximately 10 seconds until a signal sounds and the display shows 10 000 mils or 15 000km. Release button (1).

2000-2004
Turn on the ignition (standard display of the control system appears).
Press button (UP arrow) or (DOWN arrow) on the multifunction steering wheel until the FSS indicator with (Single Wrench) or (Double Wrench) and the service deadline appears in the multifunction display.
Press the reset knob to the right in the instrument cluster for about 2 seconds. This message appears in the multifunction display: “SERVICE INTERVAL? RESET WITH R BUTTON”.
To confirm hold down the reset button until you hear a signal. The service indicator now displays the reset interval.

Service oil reset Mercedes Benz E – Class

1997-2000
*Diagnostic Reset Tool Required (please refer to TOOLS page)
Manual Reset:
Turn key in steering lock to position 2.
Within 4 seconds press 0 button twice.
The present status for days or distance displays, within 10 seconds turn the electroninc key in steering lock to position 0.
Press and hold 0 button while turning electronic key in steering loack to position 2 again. The present status for days or distance displays once more. Continue to hold 0 button for approximately 10 seconds until a signal sounds and the display shows 10 000 (15000KM) for approximately 10 seconds.
Release 0 button, the status is reset.
2001-2002
*Diagnostic Reset Tool Required (please refer to TOOLS page)
Manual Reset:
Turn key in steering lock to position 2.
To call up the trip odometer and main odometer, press either of lower two buttons on left hand side of steering wheel (system select – looks like file folder) until the display appears.
Press either of the top buttons on steering wheel (arrows) until the FSS indicator appears.
Press R button on the instrument cluster for 2-4 seconds.
The display reads “DO YOU WANT TO RESET SERVICE INTERVAL? CONFIRM BY PRESSING R”
Press R button on the instrument cluster again and hold until signal sounds. The message “SERVICE INTERVAL HAS BEEN RESET” appears in the multifunction display.
2003-2004
Turn on the ignition (standard display of the control system appears).
Press button (UP arrow) or (DOWN arrow) on the multifunction steering wheel until the FSS indicator appears in the display.
Press the reset knob for about 5 seconds until the SERVICE MENU appears in the multifunction display.
Select the CONFIRMATION menu with the (+) or (-) button.
Press the menu button (looks like file 2 over lapping file folders).
The service indicator now displays the CONFIRMATION menu. The selection marker is on CONFIRM. Press the menu button (looks like 2 over lapping file folders). The service indicator now displays the CONFIRM menu. The selection marker is on STANDARD OIL.
Press the menu button (looks like 2 over lapping file folders). The words SERVICE CONFIRMED appear in the multifunction display. The service indicator is now reset.
Press the menu button on the multifunction steering wheel until the standard display appears in the multifunction display.

Service oil reset Mercedes Benz CLK – Class

1997-1999
*Diagnostic Reset Tool Required (please refer to TOOLS page)
Manual Reset:
Turn key in steering lock to position 2.
Within 4 seconds press 0 button twice.
The present status for days or distance displays, within 10 seconds turn the electroninc key in steering lock to position 0.
Press and hold 0 button while turning electronic key in steering loack to position 2 again. The present status for days or distance displays once more. Continue to hold 0 button for approximately 10 seconds until a signal sounds and the display shows 10 000 (15000KM) for approximately 10 seconds.
Release 0 button, the status is reset.
2000-2003
Turn on the ignition (standard display of the control system appears).
Press button (UP arrow) or (DOWN arrow) on the multifunction steering wheel until the FSS indicator with (Single Wrench) or (Double Wrench) and the service deadline appears in the multifunction display.
Press the reset knob to the left in the instrument cluster for about 4 seconds. This message appears in the multifunction display: “DO YOU WANT TO RESET SERVICE INTERVAL? TO CONFIRM PRESS BUTTON”.
To confirm hold down the reset button until you hear a signal. The service indicator now displays the reset interval.
2004
Turn on the ignition (standard display of the control system appears).
Press button (UP arrow) or (DOWN arrow) on the multifunction steering wheel until the FSS indicator with (Single Wrench) or (Double Wrench) and the service deadline appears in the multifunction display.
Press the reset knob to the left in the instrument cluster for about 4 seconds. This message appears in the multifunction display: “SERVICE INTERVAL…TO RESET: PRESS RESET BUTTON FOR 3 SECONDS”.
To confirm hold down the reset button until you hear a signal. The service indicator now displays the reset interval.