Tag: Check

Reset the service oil light on jaguar s-type

Here’s how to do it yourself in no time works on a few different Jags….

Service Light Reset Instructions:

1 . Insert key into ignition.
2 . Press and hold the Reset switch (located on the Trip Computer Switchpack ).
3 . NOTE: The reset switch has to be released immediately after the ignition is switched ‘ON’. This is critical to enable the rest of the procedure.
Turn the key to Ignition position II and at the point of entering Ignition position II (i.e when a click is heard), instantaneously release the Reset switch.
4 . Wait one second.
5 . Press and hold the Trip switch (located on the end of the left-hand side stalk).
6 . Wait one second.
7 . Press and hold the Reset switch (whilst still holding the Trip switch).
8 . The cluster should display (within three seconds) the warning message ‘RESETTING SERVICE MODE’.
9 . Keep both buttons pressed until the warning message changes to ‘SERVICE MODE RESET’ (after ten seconds).
10 . Once the message is displayed the buttons may be released — sequence is now complete.
11 . If a Service Required message was displayed prior to the reset sequence, cycle the ignition to ‘Off’ and then back to Ignition position II and check that the message is no longer displayed.

Oil service reset Lincoln LS

2000-2006

Turn the ignition to run (one position before starting engine).
Press the STATUS control to access the System Check function.
Press RESET to reset oil %.
Press and hold the RESET control to set to 100%. After a successful reset, the message centre will display OIL LIFE SET TO 100%.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset Chevrolet GMC Trucks Suburban/Tahoe/Yukon

2000-2006

Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds.
If the Change Oil Soon light flashes the system is resetting.
Turn the ignition off and then start the engine to verify the indicator has been reset.

2007-2010

Turn the ignition to run (one position before starting engine).
Display the OIL LIFE REMAINING on the DIC (i button). If the vehicle does not have DIC buttons, the vehicle must be in P (Park) to access this display by pressing the trip odometer reset stem.
Press and hold the SET/RESET (check mark) button on the DIC , or the trip odometer reset stem if vehicle does not have DIC buttons for more than 5 seconds. The oil life will change to 100%.
Turn the ignition off and then start the engine to verify the indicator has been reset.

or

Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds.
Display the OIL LIFE REMAINING on the DIC. If the display shows 100%, the system is reset. If the vehicle has a CHANGE OIL SOON message this should be off.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset Chevrolet GMC Trucks Terrain

2010

With Driver Information Centre (DIC):
Turn the ignition to run (one position before starting engine).
Press the MENU button until vehicle information menu is displayed then scroll through the menu with the down arrow until Remaining Oil Life is selected then press SET/CLR (check button) to select.
Use up or down arrow to select YES to reset.
Confirm reset by pressing SET/CLR button.
Turn the ignition off and then start the engine to verify the indicator has been reset.
Without Driver Information Centre (DIC):
Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds.
If the Change Engine Oil Soon message goes off the system is reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset Chevrolet GMC Trucks Traverse

2009-2010

With Driver Information Centre (DIC):
Turn the ignition to run (one position before starting engine).
Press the vehicle information button (i) until OIL LIFE REMAINING displays.
Press and hold the SET/RESET (check mark) button until 100% is displayed. You will hear 3 chimes and the CHANGE ENGINE OIL SOON message will go off.
Turn the ignition off and then start the engine to verify the indicator has been reset.
Without Driver Information Centre (DIC):
Turn the ignition to run (one position before starting engine). The vehicle must be in PARK (P) to access this display. Press the trip odometer reset stem until OIL LIFE REMAINING displays.
Press and hold the trip odometer reset stem until OIL LIFE REMAINING shows 100%. You will hear 3 chimes and the CHANGE ENGINE OIL SOON message will go off.
Turn the ignition off and then start the engine to verify the indicator has been reset.