Tag: OFF

Oil light reset Jeep Renegade Concept

Many Jeep vehicles track the intervals between oil changes to alert the driver when the next oil change is needed. A light illuminates on the control panel when the internal system determines it is time for an oil change. Most Jeep mechanics reset the oil light as part of the oil change service. If you change the oil in your Jeep yourself, you can manually reset the oil light. Resetting the oil light after an oil change allows the system to accurately track the time until the next oil change is needed. The procedures described in this article apply to 2010 Jeep models.

Instructions

1.Turn the ignition switch to the “ON” position. Do not start the engine.

2.Press the accelerator pedal completely to the floor slowly three times within a 10-second span.

3.Turn the ignition switch to the “OFF” position.

4.Turn the ignition switch to the “ON” position again. The oil light should be off. If the oil light is still illuminated, repeat the previous steps.

Oil service reset Jeep Commander

Engine Oil Change Indicator System

Oil Change Required
Your vehicle is equipped with an engine oil change
indicator system. The “Oil Change Required” message
will flash in the EVIC display for approximately 10
seconds after a single chime has sounded to indicate the
next scheduled oil change interval. The engine oil change
indicator system is duty cycle based, which means the
engine oil change interval may fluctuate dependent upon
your personal driving style.
Unless reset, this message will continue to display each
time you turn the ignition switch to the ON/RUN
position. To turn off the message temporarily, press and
release the MENU button. To reset the oil change indicator
system (after performing the scheduled maintenance)
refer to the following procedure.

1. Turn the ignition switch to the ON position (Do not
start the engine).

2. Fully depress the accelerator pedal slowly three times
within 10 seconds.

3. Turn the ignition switch to the OFF/LOCK position.

NOTE: If the indicator message illuminates when you
start the vehicle, the oil change indicator system did not
reset. If necessary repeat this procedure.

Oil service reset Saturn Astra

2008

Turn the ignition key to OFF.
Press the instrument panel cluster stem until the odometer is displayed.
Press and hold the cluster stem until the letters “InSP” are displayed.
Hold the cluster stem down and turn the ignition key to RUN (one position before starting engine).
The letters “InSP” in the instrument panel cluster display will flash.
Keep the cluster stem down for at least 20 seconds and then release the stem. If the letters “InSP” and the remaining mileage for the next oil change appear in the instrument panel cluster display, the system is properly reset. Turn the ignition off and then start the engine to verify the indicator has been reset.

2009

Turn the ignition key to LOCK/OFF.
Press the instrument panel cluster stem until the odometer is displayed, then release the stem.
Re-press and hold the cluster stem until the letters “InSP” are displayed.
Press and hold the brake pedal down, hold the cluster stem down, and turn the ignition key to RUN (one position before starting engine).
The letters “InSP” in the instrument panel cluster display will flash.
Keep the cluster stem down for at least 10 seconds and release the stem and the brake pedal when the message “new remaining mileage” is displayed. Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset Chrysler Dodge Crossfire

2004-2008

Turn the ignition to run (one position before starting engine).
Within one second press the knob/button twice.
The present status for days or distance is displayed. Within 10 seconds turn the key to OFF/LOCK.
Press and hold the knob/button, while turning the distance is displayed once more. Continue to hold the knob/button. After 10 seconds, a signal sounds and the display shows 7,000 mi or 11000km for 10 seconds.
Release the knob/button.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Service oil reset Nissan Z

2006-2008
Turn the ignition to run (one position before starting engine).
When you turn the ignition key run, the system start-up warning is displayed on the screen. Read the the warning and select the OK key by pressing the ENTER button.
When the TRIP button is pressed, the following modes will display on the screen: Warning message (if any) TRIP1 > TRIP 2 > FUEL ECONOMY > MAINTENANCE > AUDIO OR OFF > TRIP 1
Select MAINTENANCE and then select the Engine Oil key using the joystick and press the ENTER button to display the screen to change the maintenance interval/RESET.
To return to the previous display after the MAINTENANCE NOTICE screen is displayed, press the BACK button.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2009-2010
Turn the ignition to run (push START/STOP button once).
Press the (square) button, located on the instrument panel just behind the steering wheel to the left, to display the SETTINGS mode.
In the setting mode screen press (circle) button to move to MAINTENANCE.
Set a desired interval by pushing (circle) button to highlight ENGINE OIL and pressing (square) button The reset mode will open up and allow you to enter the desired distance.
Select RESET and select new time or distance.
Repeat step 3 for ENGINE OIL FILTER. Turn the ignition off and then start the engine to verify the indicator has been reset.