Tag: message

Oil service reset Jeep Commander

Engine Oil Change Indicator System

Oil Change Required
Your vehicle is equipped with an engine oil change
indicator system. The “Oil Change Required” message
will flash in the EVIC display for approximately 10
seconds after a single chime has sounded to indicate the
next scheduled oil change interval. The engine oil change
indicator system is duty cycle based, which means the
engine oil change interval may fluctuate dependent upon
your personal driving style.
Unless reset, this message will continue to display each
time you turn the ignition switch to the ON/RUN
position. To turn off the message temporarily, press and
release the MENU button. To reset the oil change indicator
system (after performing the scheduled maintenance)
refer to the following procedure.

1. Turn the ignition switch to the ON position (Do not
start the engine).

2. Fully depress the accelerator pedal slowly three times
within 10 seconds.

3. Turn the ignition switch to the OFF/LOCK position.

NOTE: If the indicator message illuminates when you
start the vehicle, the oil change indicator system did not
reset. If necessary repeat this procedure.

Reset the service oil light on jaguar s-type

Here’s how to do it yourself in no time works on a few different Jags….

Service Light Reset Instructions:

1 . Insert key into ignition.
2 . Press and hold the Reset switch (located on the Trip Computer Switchpack ).
3 . NOTE: The reset switch has to be released immediately after the ignition is switched ‘ON’. This is critical to enable the rest of the procedure.
Turn the key to Ignition position II and at the point of entering Ignition position II (i.e when a click is heard), instantaneously release the Reset switch.
4 . Wait one second.
5 . Press and hold the Trip switch (located on the end of the left-hand side stalk).
6 . Wait one second.
7 . Press and hold the Reset switch (whilst still holding the Trip switch).
8 . The cluster should display (within three seconds) the warning message ‘RESETTING SERVICE MODE’.
9 . Keep both buttons pressed until the warning message changes to ‘SERVICE MODE RESET’ (after ten seconds).
10 . Once the message is displayed the buttons may be released — sequence is now complete.
11 . If a Service Required message was displayed prior to the reset sequence, cycle the ignition to ‘Off’ and then back to Ignition position II and check that the message is no longer displayed.

Oil service reset Volkswagen Jetta

1993-1999
Turn the ignition to run (one position before starting engine).
Press and hold the button located under the speedometer.
Switch ignition off and release button. Message OIL appears in the display.
Press MINUTE button of digital clock or button for setting analog clock only as long as 5 dashes appears in display.
Turn the ignition off and then start the engine to verify the indicator has been reset.

2000-2004

Reset may be similar to previous year or other models – Oil Reset will verify and update site.

2005-2010

Manual Reset:
Turn the ignition to run (one position before starting engine).
Press and HOLD the trip-odometer button “0.0”.
Turn your key to run (one position before starting engine).
Release the trip-odometer button.
Push and release the Clock Minute Set Button “min”.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset Volkswagen Cabrio

1995-2002

Turn the ignition to run (one position before starting engine).
Press and hold the button located under the speedometer.
Switch ignition off and release button. Message OIL appears in the display.
Press MINUTE button of digital clock or button for setting analog clock only as long as 5 dashes appears in display.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset Saturn Outlook

2007-2009

If your vehicle does not have Driver Information Center (DIC) buttons:
Turn the ignition to run (one position before starting engine).
Press the trip odometer reset stem until OIL LIFE REMAINING displays.
Press and hold the trip odometer reset stem until OIL LIFE REMAINING shows 100%. You will hear 3 chimes and the CHANGE ENGINE OIL SOON message will go off.
Turn the ignition off and then start the engine to verify the indicator has been reset.

If your vehicle has Driver Information Center (DIC) buttons:
Turn the ignition to run (one position before starting engine).
Press the vehicle information button (square) until OIL LIFE REMAINING displays.
Press and hold the set/reset button (arrow) until 100% is displayed. You will hear 3 chimes and the CHANGE ENGINE OIL SOON message will go off.
Turn the ignition off and then start the engine to verify the indicator has been reset.